Assignment Help on Hand Gesture Controlled Robot

MICROCONTROLLER:

                      Microcontroller is a programmable device. A microcontroller has a CPU in addition to a fixed amount of RAM, ROM, I/O ports and a timer embedded all on a single chip. The fixed amount of on-chip ROM, RAM and number of I/O ports in microcontrollers makes them ideal for many applications in which cost and space are critical.

                        The Intel 8051 is Harvard architecture, single chip microcontroller (µC) which was developed by Intel in 1980 for use in embedded systems. It was popular in the 1980s and early 1990s, but today it has largely been superseded by a vast range of enhanced devices with 8051-compatible processor cores that are manufactured by more than 20 independent manufacturers including Atmel, Infineon Technologies and Maxim Integrated products

                          8051 is an 8-bit processor, meaning that the CPU can work on only 8 bits of data at a time. Data larger than 8 bits has to be broken into 8-bit pieces to be processed by the CPU. 8051 is available in different memory types such as UV-EPROM, Flash and NV-RAM.

                       The present project is implemented on Keil Uvision. In order to program the device, Proload tool has been used to burn the program onto the microcontroller.

1.1.1 AT89S52:

                       The AT89s52 is a low-voltage, high-performance CMOS 8-bit microcomputer with 8K bytes of Flash programmable memory. The device is manufactured using Atmel’s high density nonvolatile memory technology and is compatible with the industry-standard MCS-51 instruction set.        

Fig: 1.1:AT89S52 IC

                            The on chip flash allows the program memory to be reprogrammed in system or by a conventional non-volatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89s52 is a powerful microcomputer, which provides a highly flexible and cost-effective solution to many embedded control applications.

                          In addition, the AT89s52 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The power-down mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset.

PORT DESCRIPTION:-

                        It has 4 ports each having 8 pins .Total 32 pins. 

Port 0

Port 0 is an 8-bit open drain bidirectional I/O port. As an output port, each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as high impedance inputs. Port 0 also receives the code bytes during Flash programming and outputs the code bytes during Program verification. External pull-ups are required during program verification.

Port 1

Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins, they are pulled high by the internal pull-ups and can be used as inputs. In addition, P1.0 and P1.1 can be configured to be the timer/counter 2 external count input (P1.0/T2) and the timer/counter 2 trigger input (P1.1/T2EX). Port 1 also receives the low-order address bytes during Flash programming and verification.

Port 2

Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups. During accesses to external data memory that uses 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 Special Function Register. The port also receives the high-order address bits and some control signals during Flash programming and verification

Port 3

Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pull-ups. Port 3 receives some control signals for Flash programming and verification.

1.2 ANALOG   TO DIGITAL CONVERTOR (ADC)   

                          An analog-to-digital convertor  is a device that converts a continuous physical quantity (usually voltage) to a digital number that represents the quantity's amplitude.

                           The conversion involves quantization of the input, so it necessarily introduces a small amount of error. Instead of doing a single conversion, an ADC often performs the conversions periodically. The result is a sequence of digital values that have converted a continuous-time and continuous-amplitude analog signal to a discrete-time and discrete-amplitude digital signal.

                            An ADC is defined by its bandwidth and its signal to noise ratio. The actual bandwidth of an ADC is characterized primarily by its sampling rate, and to a lesser extent by how it handles errors such as aliasing.

1.2.1 ADC-0804

                             The ADC 0804 A/D Converter is an 8bit A/D converter that uses successive approximation to convert the analog inputs to the digital output. The ADC0804 has four major sections namely the Comparator, the control logic, the digital counter and a 256R ladder D/A converter. For any analog input, the control logic will trigger the digital counter to start incrementing from zero count and these digital values are converted to analog form through a 256R ladder network.

                             This 256R network consists of a number of resistors of fixed incremental resistance that produce a representative staircase type waveform based on the output of the digital counter. The output of the ladder network then enters the comparator which has the role of comparing the input analog to the analog output of the D/A Converter. When the staircase wave form exceeds the input voltage, the comparator sends a signal to the control logic to stop counting. The value of the digital counter at the time when the comparator sends the 'stop count' signal is the digital representation of the input voltage.

                              The 0804 adc consist of single channel ,but for the application which we are using single channel is not sufficient.so it is adviced to use multi channel adc.   

1.2.2 ADC-0808

                              The ADC0808, ADC0809 data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital converter, 8-channel multiplexer and microprocessor compatible control logic. The 8-bit A/D converter uses successive approximation as the conversion technique. The converter features a high impedance chopper stabilized comparator, a 256R voltage divider with analog switch tree and a successive approximation register. The 8-channel multiplexer can directly access any of 8-single-ended analog signals.

Master the art of delivering impactful presentations under pressure with MyAssignmentHelp's expert guidance. Our specialized assistance provides invaluable tips and techniques to excel even in challenging situations. Learn how to give a good presentation under pressure with personalized support from our experienced tutors. Elevate your skills today!